Polyanionic cellulose (PAC) is a water-soluble cellulose ether derivative prepared by chemical modification of natural cellulose. It is an important water-soluble cellulose ether. It is usually used as its sodium salt and is widely used in oil drilling, especially salt water wells and offshore oil drilling. PAC-Application In Petroleum 1. The functions of PAC and CMC in oil field are as follows: - The mud containing PAC and CMC can make the well wall form thin and hard filter cake with low permeability and reduce the water loss; - After adding PAC and CMC into the mud, the drilling rig can obtain low initial shear force, make the mud easy to release the gas wrapped in it, and quickly discard the debris in the mud pit; - Like other suspended dispersions, drilling mud has a certain existence period, which can be stabilized and extended by adding PAC and CMC. 2. PAC and CMC have the following excellent performance in oilfield application: - High degree of substitution, good uniformity of substitution, high viscosity and low dosage, effectively improving mud service efficiency; - Good moisture resistance, salt resistance and alkali resistance, suitable for fresh water, seawater and saturated brine water-based mud; - The mud cake formed is of good quality and stable, which can effectively stabilize the soft soil structure and prevent shaft wall collapse; - It is suitable for mud systems with difficult solid content control and wide variation range. 3. Application characteristics of PAC and CMC in oil drilling: - It has high water loss control ability, especially efficient fluid loss reducer. With low dosage, it can control water loss at a high level without affecting other properties of mud; - It has good temperature resistance and excellent salt resistance. It can still have good water loss reduction ability and certain rheology under a certain salt concentration. The viscosity is almost unchanged after dissolving in salt water. It is especially suitable for offshore drilling and deep wells; - It can well control the rheology of mud and has good thixotropy. It is suitable for any water-based mud in fresh water, seawater and saturated brine; - In addition, PAC is used as cementing fluid to prevent fluid from entering pores and fractures; - The filter press fluid prepared with PAC has good resistance to 2% KCl solution (it must be added when preparing filter press fluid), good solubility, convenient use, can be prepared on site, fast gel forming speed and strong sand carrying capacity. When used in low permeability formation, its filter press effect is more excellent. Detail Parameters Addition amount (%) Oil production fracturing agent 0.4-0.6% Drilling treatment agent 0.2-0.8% If you need to customize, you can provide detailed formula and process. Indicators PAC-HV PAC-LV Color White or light yellowpowder White or light yellow powder or particles water content 10.0% 10.0% PH 6.0-8.5 6.0-8.5 Degree of substitution 0.8 0.8 sodium chloride 5% 2% Purity 90% 90% Particle size 90% pass 250 microns(60 mesh) 90% pass 250 microns (60 mesh) Viscosity (b) 1% aqueous solution 3000-6000mPa.s 10-100mPa.s Application performance Model Index AV FL PAC-ULV ≤10 ≤16 PAC－LV1 ≤30 ≤16 PAC－LV2 ≤30 ≤13 PAC－LV3 ≤30 ≤13 PAC－LV4 ≤30 ≤13 PAC－HV1 ≥50 ≤23 PAC－HV2 ≥50 ≤23 PAC－HV3 ≥55 ≤20 PAC－HV4 ≥60 ≤20 PAC－UHV1 ≥65 ≤18 PAC－UHV2 ≥70 ≤16 PAC－UHV3 ≥75 ≤16

VAE emulsion is short of vinyl acetate copolymer emulsion, it is the emulsion product which uses vinyl acetate monomer and ethylene monomer as raw material with the method of press copolymerization. The characteristics of the process is using outer loop to expose the heat of reaction, the polymer is fast, the capacity is large, the process of polymer is controlled by computer, the product quality is stable, low depletion, little pollution. The product is non-toxic, tasteless, it is environmental protection product which is recommended by the government. VAE emulsion is a kind of milky liquid. Because of ethylene copolymerization monomer, VAE emulsion has the characteristic of inner plasticizing, and filming, weather resistance, adhesive, and compatible, weak acid and alkali resistance. Adhesive basic material VAE emulsion can be used as adhesive basic material, such as wood and wooden products, paper and paper products, package composite materials, plastics, structure. Paint basic material VAE emulsion can be used as inner wall paint, elasticity paint, waterproof paint of roof and groundwater, the basic material of fireproof and heat preservation paint, it also can be used as the basic material of the caulking of structure, sealing adhesive. Paper sizing and glazing VAE emulsion can sizing and glazing many kinds of paper, it is excellent material of producing many kinds of advanced paper. VAE emulsion can be used as the basic material of no-woven adhesive. Cement modifier VAE emulsion can be mixed with cement mortal so that improving the property of the cement product. VAE emulsion can be used as the adhesive, such as tufted carpet, needle carpet. weaving carpet, artificial fur, electrostatic flocking, high-level structure assemble carpet. Product advantages and application scope GW-705/GW-706: The common adhesive with high quality, excellent innitial adhesion, mechanical stability Widely used in paper product, wooden package, cement, cigarette. GW-707/GW-707H: The biggest advantages is its good water resistance in the condition of the static load, it has excellent adhesive Widely used in paper product, package, coil adhesive, high-speed adhesive, water resistance coating. GW-102/GW-102H: It has better adhesive. The compatibility of material is good Widely used in Shoes Adhesive, Clothes Adhesive, Wood, Paper Painting, Furnishing Detail parameters Product Name Solid Content %≥ PH Value Viscosity(25℃) Mpa.s Remain Vam %≤ Particle Size um≤ Dilution Stability %≤ Minimum film-forming Ethylene content % temperature ℃ GW-705 54.4 4.0-6.0 1500-2500 0.5 2 3.5 0 16±2 GW-706 54.4 4.0-6.0 2500-3300 0.5 2 3.5 0 16±2 GW-707 54.4 4.0-6.0 500-1000 0.5 2 5 0 16±2 GW-707H 54.4 4.0-6.0 1000-1500 0.5 2 3.5 0 16±2 GW-102 55 4.0-6.5 3500-4000 0.5 0.2-2.0 3.5 16.5 GW-102H 55.5 4.0-6.5 4000-4500 0.5 0.2-2.0 3.5 17

Polyanionic cellulose (PAC) is a water-soluble cellulose ether derivative prepared by chemical modification of natural cellulose. It is an important water-soluble cellulose ether. It is usually used as its sodium salt and is widely used in oil drilling, especially salt water wells and offshore oil drilling. PAC-Application In Petroleum 1. The functions of PAC and CMC in oil field are as follows: - The mud containing PAC and CMC can make the well wall form thin and hard filter cake with low permeability and reduce the water loss; - After adding PAC and CMC into the mud, the drilling rig can obtain low initial shear force, make the mud easy to release the gas wrapped in it, and quickly discard the debris in the mud pit; - Like other suspended dispersions, drilling mud has a certain existence period, which can be stabilized and extended by adding PAC and CMC. 2. PAC and CMC have the following excellent performance in oilfield application: - High degree of substitution, good uniformity of substitution, high viscosity and low dosage, effectively improving mud service efficiency; - Good moisture resistance, salt resistance and alkali resistance, suitable for fresh water, seawater and saturated brine water-based mud; - The mud cake formed is of good quality and stable, which can effectively stabilize the soft soil structure and prevent shaft wall collapse; - It is suitable for mud systems with difficult solid content control and wide variation range. 3. Application characteristics of PAC and CMC in oil drilling: - It has high water loss control ability, especially efficient fluid loss reducer. With low dosage, it can control water loss at a high level without affecting other properties of mud; - It has good temperature resistance and excellent salt resistance. It can still have good water loss reduction ability and certain rheology under a certain salt concentration. The viscosity is almost unchanged after dissolving in salt water. It is especially suitable for offshore drilling and deep wells; - It can well control the rheology of mud and has good thixotropy. It is suitable for any water-based mud in fresh water, seawater and saturated brine; - In addition, PAC is used as cementing fluid to prevent fluid from entering pores and fractures; - The filter press fluid prepared with PAC has good resistance to 2% KCl solution (it must be added when preparing filter press fluid), good solubility, convenient use, can be prepared on site, fast gel forming speed and strong sand carrying capacity. When used in low permeability formation, its filter press effect is more excellent. Detail Parameters Addition amount (%) Oil production fracturing agent 0.4-0.6% Drilling treatment agent 0.2-0.8% If you need to customize, you can provide detailed formula and process. Indicators PAC-HV PAC-LV Color White or light yellowpowder White or light yellow powder or particles water content 10.0% 10.0% PH 6.0-8.5 6.0-8.5 Degree of substitution 0.8 0.8 sodium chloride 5% 2% Purity 90% 90% Particle size 90% pass 250 microns(60 mesh) 90% pass 250 microns (60 mesh) Viscosity (b) 1% aqueous solution 3000-6000mPa.s 10-100mPa.s Application performance Model Index AV FL PAC-ULV ≤10 ≤16 PAC－LV1 ≤30 ≤16 PAC－LV2 ≤30 ≤13 PAC－LV3 ≤30 ≤13 PAC－LV4 ≤30 ≤13 PAC－HV1 ≥50 ≤23 PAC－HV2 ≥50 ≤23 PAC－HV3 ≥55 ≤20 PAC－HV4 ≥60 ≤20 PAC－UHV1 ≥65 ≤18 PAC－UHV2 ≥70 ≤16 PAC－UHV3 ≥75 ≤16

Product Uses Polyvinyl alcohol (PVA) have a wide range of uses. In the textile industry, it is used as warp slurry, textile finishing agent, and adhesives of non-woven fabrics. In the construction industry, it is used as cement additives, molding plate adhesives, and building glues. In the chemical industry, it is used semulsion stabilizer and dispersants. In the papermaking industry, it is used as adhesives. In addtion, It can be used in cosmetics industry, agriculture, pharmaceutical industry, etc. Detailed Parameters Wanwei PVA index Name Viscosity (mPa.s) Average degree of polymerization Alcoholysis degree(mol %) molecular weight Volatile consituent(%) Sodium acetate(%) Ash (%) PH 04-88(L) 3.0-4.5 / 86.0-90.0 / 7.0 2.8 1.0 5-7 04-99(L) 3.0-4.5 300-450 98.0-100.0 13200-19800 7.0 2.8 1.0 5-7 05-88(L) 4.0-6.0 / 86.0-90.0 17600-26400 7.0 2.8 1.0 5-7 05-99(L) 4.0-6.0 450-600 98.0-100.0 19800-26400 7.0 2.8 1.0 5-7 10-92(L) 8.0-13.0 / 90.0-94.0 / 7.0 2.8 1.0 5-7 10-99(L) 9.0-14.0 900-1100 98.0-100.0 39600-48400 7.0 2.8 1.0 5-7 14-92(L) 13.0-18.0 / 90.0-94.0 / 7.0 2.8 1.0 5-7 15-99(L) 20.0-26.0 1450-1650 98.0-100.0 63800-72600 7.0 2.8 1.0 5-7 17-80(L) 18.0-24.0 / 78.0-82.0 / 7.0 2.8 1.0 5-7 17-88(L) 20.0-28.0 / 86.0-90.0 72600-81400 7.0 2.8 1.0 5-7 17-92(L) 20.0-30.0 / 90.0-94.0 72600-81400 7.0 2.8 1.0 5-7 17-95(L) 20.0-30.0 / 94.0-96.0 72600-81400 7.0 2.8 1.0 5-7 17-96(L) 20.0-30.0 / 94.0-98.0 / 7.0 2.8 1.0 5-7 17-97(L) 21.0-31.0 1650-1850 96.0-98.0 72600-81400 7.0 2.8 1.0 5-7 17-98(L) 20.0-26.0 1600-1800 97.0-99.0 70400-79200 7.0 2.8 1.0 5-7 17-99(L) 20.0-26.0 1680-1850 98.0-100.0 73900-82700 7.0 2.8 1.5 5-7 17-99(H) 20.0-26.0 1650-1850 98.5-100.0 72600-81400 9.0 7.0 3.0 5-7 19-99(L) 26.0-32.0 1800-2000 98.0-100.0 79200-88000 7.0 2.8 1.0 5-7 19-99(H) 26.0-34.0 1800-2000 98.5-100.0 79200-88000 9.0 7.0 1.5 5-7 20-88(L) 28.0-40.0 / 86.0-90.0 81400-94600 7.0 2.8 3.0 5-7 20-99(L) 32.0-40.0 2000-2200 98.0-100.0 88000-96800 7.0 2.8 1.5 5-7 20-99(H) 34.0-42.0 2000-2300 98.5-100.0 88000-101200 9.0 7.0 1.0 5-7 22-99(L) 40.0-48.0 2200-2400 98.0-100.0 96800-105600 7.0 2.8 1.5 5-7 23-99(H) 42.0-55.0 2300-2600 98.5-100.0 101200-114400 9.0 7.0 3.0 5-7 24-88(L) 40.0-55.0 / 86.0-90.0 101200-110000 7.0 2.8 1.5 5-7 24-99(L) 48.0-60.0 2400-2600 98.0-100.0 105600-114400 7.0 2.8 1.5 5-7 26-99(L) 60.0-75.0 2600-2800 98.0-100.0 114400-123200 7.0 2.8 3.0 5-7 28-99(L) 75.0-90.0 2800-3000 98.0-100.0 123200-132000 7.0 2.8 1.5 5-7

Polyvinyl chloride resin (PVC): white powder in appearance. It is widely used in industrial products, floor leather, artificial leather, pipes, wires and cables, packaging film, foaming materials, etc. the packaging is 25kg / bag, 600kg / bag and 1200kg / bag. DG-1300: production of cable material, fresh-keeping film, etc. DG-1000k: production of plastic profiles, pipes, etc DG-1000s: production of packaging film, etc DG-800: production of packaging sheet, medical sheet, etc DG-700: production of pipe fittings, foamed plates, etc Main indicators of product standard (Q / 12 hg5220-2019) Project DG-1300 DG-1000K DG-1000S DG-700 DG-800 Average degree of polymerization P 1221-1380 981-1080 981-1080 651-750 751-850 Apparent density, g / ml 0.46-0.54 0.51-0.57 0.51-0.57 0.53-0.61 0.54-0.60 Whiteness (160 ℃, 10min),% ≥ 78 78 78 75 78 Corresponding table of degree of polymerization, viscosity and K value Average degree of polymerization 2351-2650 1221-1380 981-1080 771-870 751-750 651-750 481-600 401-500 Viscosity, ml / g 222-248 125-138 105-138 87-96 86-94 73-86 62-72 57-64 K value 89-93 70-73 65-67 60-62 59-62 55-59 51-55 49-51

(polyvinyl alcohol · PVOH · PVA) is widely used by users at home and abroad in the use of industrial raw materials and processing agents such as binder, paper coating agent, emulsifier, suspending agent, fiber and film due to its excellent water solubility, adhesion, film-forming and chemical stability. Since 1927, with advanced technology and unremitting research, many special varieties have been developed successively. Many varieties are produced under strict management, and their quality system meets the international standard of iso9001:2015. Grossinor products are widely praised as indispensable materials in various industrial fields, providing active support for future technologies. Scope of Application ◆ Paper processing ◆ Emulsifier ◆ Adhesive, adhesive ◆ Medicine ◆ Cosmetics ◆ Powder chemical building materials ◆ Fiber processing industry ◆ Polymerization dispersant Detail Parameters Name Index Alcoholysis degree(mol %) Viscosity (mPa.s) Volatile consituent(%) PH Ash (%) GL-05 86.5-89.0 4.8-5.8 5.0 5-7 0.7 GL-05AF 86.5-89.0 4.8-5.8 5.0 5-7 0.7 GH-20R 86.5-89.0 40.0-46.0 5.0 5-7 0.7 GH-22 86.5-89.0 45.0-52.0 5.0 5-7 0.7 GM-14R 86.5-89.0 20.5-24.5 5.0 5-7 0.7 GM-14AF 86.5-89.0 20.5-24.5 5.0 5-7 0.7 GH-17R 86.5-89.0 27.0-33.0 5.0 5-7 0.7 GH-17Y 86.5-89.0 27.0-33.0 5.0 5-7 0.7 N-300 98.0-99.0 25.0-30.0 5.0 5-7 0.7

Coating grade CMC model:  IM6D IVH9D CMC can be used in water-based interior and exterior wall coatings instead of HEC, and has good cost performance. Through the chemical modification of the product surface, it has good dispersion performance in aqueous solution, no agglomeration, fast dissolution speed and convenient use. It is an economic multi-purpose additive that can be used in coatings. It has the functions of thickening, controlling leveling, water retention and maintaining dispersion stability. Compared with other cellulose ether products, it shows better splash resistance. CMC-Application In Coating Industry - After chemical treatment, it has good dispersion; - It can dissolve quickly after adding alkali; - The solution has no fiber and good transparency; - Very few gel particles, filter screen will not be blocked, easy to use. - Various viscosity ranges and good viscosity stability; - The reaction is uniform and has good resistance to enzyme denaturation; - Good heat resistance. Detail Parameters Addition amount (%) IM6D 0.3-1.0% IVH9D 0.3-1.0% If you need to customize, you can provide detailed formula and process. Indicators   IVH9D IM6D Color White or light yellow White or light yellow water content 10.0% 10.0% PH 6.0-8.5 6.0-8.5 Degree of substitution 0.8 0.6 sodium chloride 5% 2% Purity 90% 95% Particle size 90% pass 250 microns (60 mesh) 90% pass 250 microns (60 mesh) Viscosity (b) 1% aqueous solution 1000-3000mPas 100-200mPas

Putty powder CMC model: 348,218A CMC is a derivative with ether structure obtained by chemical modification of natural cellulose. It is a water-soluble gum, which can be dissolved in cold and hot water. Its aqueous solution has the functions of bonding, thickening, emulsifying, dispersing, suspending, stabilizing and film-forming. CMC-Application In Putty Powder CMC, as an additive for building putty, provides good performance in construction, water retention and flow resistance. Detail Parameters Addition amount (%)  348 0.8-1.5% 218A 0.6-1.2% If you need to customize, you can provide detailed formula and process. 348 218A colour White flocculent White or light yellow powder water content 45.0% 10.0% PH 8.0-12.0 8.0-10.0 Degree of substitution 0.5 0.5 Purity 50% 50% Particle size - 98% pass 250 microns (60 mesh) Viscosity (b) 1% aqueous solution 50-500mPas 100-500mPas

The Redispersible Polymer Powder is powder materials with Green Environmental Protection, Building Energy Saving ,high quality and Multipurpose which also is important functional additive in dry-mixed mortar. The powder can improve the mortar's performance, increase the strength of mortar and bond strength onto substrates, improve flexibility and mortar deformation, compressive strength, flexural strength, wear resistance, toughness, adhesion, water-holding capacity and constructability. In addition, it can make mortar waterproof. Redispersible polymer powder is mainly applied to internal and external putty, ceramic tile adhesive, ceramic tile Crack Sealer, dry powder interfacial agent, Exterior wall using outside insulation mortar, self flowing mortar, repair mortar, decorative plaster, waterproof mortar etc. WWJF-8010-Product Uses WWJF--8010 is a type of re-dispersible polymer powder copolymerized with VAC/VeoVa. Application Scope 1. Self flowing floor material 2. Exterior wall using outside insulation bonded mortar 3. Dry powder interfacial agent Characteristics : The product can be dispersed in water, which can improve adhesive force between mortar and its supports; high impact        resistance; it can also improve the constructability and mechanical properties of the mortar. Package: Compound triple paper-plastic bag. N.W. is 25 kg/per bag Shelf life: 180 days. Exceeding valid period, if the products have not lumped it can still be used. WWJF-8020-Product Uses WWJF--8020is a type of re-dispersible polymer powder copolymerized with VAC/VeoVa/VAE. Application Scope 1. Exterior wall using outside insulation bonded mortar 2. Flexible Putty for Exterior Wall 3. Crack Sealer 4. Cement-Based polymer mortar product with high demand of flexility. Characteristics The product can be dispersed in water, which can improve adhesive force between mortar and its supports; it can also improve the constructability and mechanical properties of the mortar. Package: Compound triple paper-plastic bag. N.W. is 25kg/per bag Shelf life: 180 days. Exceeding valid period, if the products have not lumped it can still be used. WWJF-8040-Product Uses WWJF--8040 is a type of re-dispersible polymer powder copolymerized with Pva/Eva. Application Scope 1. Adhesive mortar 2. Tile adhesive Characteristics : Soft emulsion powder; it can be emulsified with water and improve cohesion between mortar and its General supports, it can also improve the constructability and Mechanical properties of the mortar. Package:Compound triple paper-plastic bag. N.W. is 25 kg/per bag Shelf life: 180 days. Exceeding valid period, if the products has no lumped it can still be used. WWJF-8050-Product Uses WWJF-8050 is a redispersible rubber powder blended by P / E copolymerization Application Scope 1. Exterior wall external insulation plastering mortar 2. Ceramic tile pointing agent 3. Flexible putty for exterior wall 4. Ceramic tile adhesive Package:Compound triple paper-plastic bag. N.W. is 25 kg/per bag Shelf life: 180 days. Exceeding valid period, if the products has no lumped it can still be used. Detail parameters Type Non-volatile %≥ Density (kg/m3) Ash(650℃±25℃)%≤ Tg ℃ Minimum film-forming temperature ℃ Fineness (≥150m) %≤ Average particle diameter (D50) μm ≤ WWJF-8010 98 450±50 12±2 10 0±2 10 60 - 100 WWJF-8020 98 450±50 12±2 5 0±2 10 60 - 100 WWJF-8030 98 450±50 12±2 8 0±2 10 60 - 100 WWJF-8040 98 450±50 12±2 15 0±2 10 60 - 100 WWJF-8050 98 450±50 12±2 -6 0±2 10 60 - 100 WWJF-6010 98 450±50 16±2 10 0±2 10 60 - 100

Mixed cementitious mortars have become a very important part of the mortar industry in Global and play anindispensable role due to the market promotion and national support of policy. In development of mortars, cellulose ether is animportant activist. Ordinary mortar is economically demanding in which cement level is small, but the requirements for its operating and machine spraying properties are still high, so sand grading and additives are important. In addition, mechanical application will become a definite tendency of development of ready-mixed mortar, cellulose ether will make mechanical application possible. Product Features Increase water demand. High water retention, prolong the operating time of the material, improve the working performance, avoid the phenomenon of crusting, and help to improve the mechanical strength of the material. Improved operating performance, provide lubrication and uniform texture, so that the surface of the material is easier to wipe, thus improving the construction efficiency, and improve the resistance to cracking of putty. Improve homogeneity, and improve vertical flow resistance. HPMC for tile adhesive Ceramic tiles have high performance and excellent work efficiency when pasted on various substrates. Skid resistance and better opening time are the key to better adhesive requirements. HPMC for wall putty HPMC is non-ionic cellulose ether made from natural cotton fiber under series of chemical processing. It’s odorless, tasteless and non-toxic white powder, can be dissolved in normal water to form a transparent viscous solution with the properties of thickening,binding, dispersing, emulsifying, film coating, suspending, absorbing, gelling, water retention and colloid protection. cellulose ethers impart the following excellent properties to mortar: 一Optimized wetting ability to the substrate 一 Advanced water retention ability 一 good spraying and pumping performance 一 Improve cement hydration by bonding strength Product Description 1) Appearance: HPMC is a nonionic cellulose ether, white grayish-white powder or granule,odorless and flavorless, soluble in cold water, glacial acetic acid, ethanol, methanol and propylene glycol, slightly soluble in acetone depending on the degree of substitutions, practically insoluble in hot water, ethylene glycol and toluene. HPMC is dissolved in a mixture of 10% methanol and 90% methylene chloride to form colloidal solutions. 2) The solution of HPMC has surface activity, high transparency, and stable performance. When heated at certain temperature, the solution becomes cloudy or forms flocculent gel. However, the solution becomes clear again after cooling. Different types of HPMC have different gelation temperatures. The solubility varies with the viscosity. The lower the viscosity, the higher solubility it has. The different types of HPMC are different in some properties and their solubility in water is not affected by pH. 3) Particle sizes: 100% pass rate in 80 mesh. 4) Apparent density: 0.25-0.70 g/mL (usually about 0.5 g/mL),specific density 1.26-1.31mL. 5) Color change temperature:190-200°C; Carbonization temperature:280-300°C. 6) Surface tension:42-56 dyn/cm (2% aqueous solution). 7) The higher methoxy content in HPMC, the lower gelation temperature, and the higher solubility in water and surface activity. 8) HPMC has some other characteristics, for example, thickening property, pH stability, retention of water, excellent film-forming property, good disperse and adhesion ability. Detail parameters Item Index Content of Methoxyl (%) 24.0-30.0 Content of Hydroxy propyl (%) 7.0-12.0 Temperature of gelation 54℃—90℃ Moisture 5% max Ash 5% max PH value 6—8 Appearance White powder Fitness 80—100mesh Viscosity 100 to 200000 it can be customized

Mixed cementitious mortars have become a very important part of the mortar industry in Global and play anindispensable role due to the market promotion and national support of policy. In development of mortars, cellulose ether is animportant activist. Ordinary mortar is economically demanding in which cement level is small, but the requirements for its operating and machine spraying properties are still high, so sand grading and additives are important. In addition, mechanical application will become a definite tendency of development of ready-mixed mortar, cellulose ether will make mechanical application possible. Product Features Increase water demand. High water retention, prolong the operating time of the material, improve the working performance, avoid the phenomenon of crusting, and help to improve the mechanical strength of the material. Improved operating performance, provide lubrication and uniform texture, so that the surface of the material is easier to wipe, thus improving the construction efficiency, and improve the resistance to cracking of putty. Improve homogeneity, and improve vertical flow resistance. HPMC for tile adhesive Ceramic tiles have high performance and excellent work efficiency when pasted on various substrates. Skid resistance and better opening time are the key to better adhesive requirements. HPMC for wall putty HPMC is non-ionic cellulose ether made from natural cotton fiber under series of chemical processing. It’s odorless, tasteless and non-toxic white powder, can be dissolved in normal water to form a transparent viscous solution with the properties of thickening,binding, dispersing, emulsifying, film coating, suspending, absorbing, gelling, water retention and colloid protection. cellulose ethers impart the following excellent properties to mortar: 一Optimized wetting ability to the substrate 一 Advanced water retention ability 一 good spraying and pumping performance 一 Improve cement hydration by bonding strength Product Description 1) Appearance: HPMC is a nonionic cellulose ether, white grayish-white powder or granule,odorless and flavorless, soluble in cold water, glacial acetic acid, ethanol, methanol and propylene glycol, slightly soluble in acetone depending on the degree of substitutions, practically insoluble in hot water, ethylene glycol and toluene. HPMC is dissolved in a mixture of 10% methanol and 90% methylene chloride to form colloidal solutions. 2) The solution of HPMC has surface activity, high transparency, and stable performance. When heated at certain temperature, the solution becomes cloudy or forms flocculent gel. However, the solution becomes clear again after cooling. Different types of HPMC have different gelation temperatures. The solubility varies with the viscosity. The lower the viscosity, the higher solubility it has. The different types of HPMC are different in some properties and their solubility in water is not affected by pH. 3) Particle sizes: 100% pass rate in 80 mesh. 4) Apparent density: 0.25-0.70 g/mL (usually about 0.5 g/mL),specific density 1.26-1.31mL. 5) Color change temperature:190-200°C; Carbonization temperature:280-300°C. 6) Surface tension:42-56 dyn/cm (2% aqueous solution). 7) The higher methoxy content in HPMC, the lower gelation temperature, and the higher solubility in water and surface activity. 8) HPMC has some other characteristics, for example, thickening property, pH stability, retention of water, excellent film-forming property, good disperse and adhesion ability. Detail parameters Item Index Content of Methoxyl (%) 24.0-30.0 Content of Hydroxy propyl (%) 7.0-12.0 Temperature of gelation 54℃—90℃ Moisture 5% max Ash 5% max PH value 6—8 Appearance White powder Fitness 80—100mesh Viscosity 100 to 200000 it can be customized

Polyanionic cellulose (PAC) is a water-soluble cellulose ether derivative prepared by chemical modification of natural cellulose. It is an important water-soluble cellulose ether. It is usually used as its sodium salt and is widely used in oil drilling, especially salt water wells and offshore oil drilling. PAC-Application In Petroleum 1. The functions of PAC and CMC in oil field are as follows: - The mud containing PAC and CMC can make the well wall form thin and hard filter cake with low permeability and reduce the water loss; - After adding PAC and CMC into the mud, the drilling rig can obtain low initial shear force, make the mud easy to release the gas wrapped in it, and quickly discard the debris in the mud pit; - Like other suspended dispersions, drilling mud has a certain existence period, which can be stabilized and extended by adding PAC and CMC. 2. PAC and CMC have the following excellent performance in oilfield application: - High degree of substitution, good uniformity of substitution, high viscosity and low dosage, effectively improving mud service efficiency; - Good moisture resistance, salt resistance and alkali resistance, suitable for fresh water, seawater and saturated brine water-based mud; - The mud cake formed is of good quality and stable, which can effectively stabilize the soft soil structure and prevent shaft wall collapse; - It is suitable for mud systems with difficult solid content control and wide variation range. 3. Application characteristics of PAC and CMC in oil drilling: - It has high water loss control ability, especially efficient fluid loss reducer. With low dosage, it can control water loss at a high level without affecting other properties of mud; - It has good temperature resistance and excellent salt resistance. It can still have good water loss reduction ability and certain rheology under a certain salt concentration. The viscosity is almost unchanged after dissolving in salt water. It is especially suitable for offshore drilling and deep wells; - It can well control the rheology of mud and has good thixotropy. It is suitable for any water-based mud in fresh water, seawater and saturated brine; - In addition, PAC is used as cementing fluid to prevent fluid from entering pores and fractures; - The filter press fluid prepared with PAC has good resistance to 2% KCl solution (it must be added when preparing filter press fluid), good solubility, convenient use, can be prepared on site, fast gel forming speed and strong sand carrying capacity. When used in low permeability formation, its filter press effect is more excellent. Detail Parameters Addition amount (%) Oil production fracturing agent 0.4-0.6% Drilling treatment agent 0.2-0.8% If you need to customize, you can provide detailed formula and process. Indicators PAC-HV PAC-LV Color White or light yellowpowder White or light yellow powder or particles water content 10.0% 10.0% PH 6.0-8.5 6.0-8.5 Degree of substitution 0.8 0.8 sodium chloride 5% 2% Purity 90% 90% Particle size 90% pass 250 microns(60 mesh) 90% pass 250 microns (60 mesh) Viscosity (b) 1% aqueous solution 3000-6000mPa.s 10-100mPa.s Application performance Model Index AV FL PAC-ULV ≤10 ≤16 PAC－LV1 ≤30 ≤16 PAC－LV2 ≤30 ≤13 PAC－LV3 ≤30 ≤13 PAC－LV4 ≤30 ≤13 PAC－HV1 ≥50 ≤23 PAC－HV2 ≥50 ≤23 PAC－HV3 ≥55 ≤20 PAC－HV4 ≥60 ≤20 PAC－UHV1 ≥65 ≤18 PAC－UHV2 ≥70 ≤16 PAC－UHV3 ≥75 ≤16

Polyvinyl chloride resin (PVC): white powder in appearance. It is widely used in industrial products, floor leather, artificial leather, pipes, wires and cables, packaging film, foaming materials, etc. the packaging is 25kg / bag, 600kg / bag and 1200kg / bag. DG-1300: production of cable material, fresh-keeping film, etc. DG-1000k: production of plastic profiles, pipes, etc DG-1000s: production of packaging film, etc DG-800: production of packaging sheet, medical sheet, etc DG-700: production of pipe fittings, foamed plates, etc Main indicators of product standard (Q / 12 hg5220-2019) Project DG-1300 DG-1000K DG-1000S DG-700 DG-800 Average degree of polymerization P 1221-1380 981-1080 981-1080 651-750 751-850 Apparent density, g / ml 0.46-0.54 0.51-0.57 0.51-0.57 0.53-0.61 0.54-0.60 Whiteness (160 ℃, 10min),% ≥ 78 78 78 75 78 Corresponding table of degree of polymerization, viscosity and K value Average degree of polymerization 2351-2650 1221-1380 981-1080 771-870 751-750 651-750 481-600 401-500 Viscosity, ml / g 222-248 125-138 105-138 87-96 86-94 73-86 62-72 57-64 K value 89-93 70-73 65-67 60-62 59-62 55-59 51-55 49-51

Polyvinyl chloride resin (PVC): white powder in appearance. It is widely used in industrial products, floor leather, artificial leather, pipes, wires and cables, packaging film, foaming materials, etc. the packaging is 25kg / bag, 600kg / bag and 1200kg / bag. DG-1300: production of cable material, fresh-keeping film, etc. DG-1000k: production of plastic profiles, pipes, etc DG-1000s: production of packaging film, etc DG-800: production of packaging sheet, medical sheet, etc DG-700: production of pipe fittings, foamed plates, etc Main indicators of product standard (Q / 12 hg5220-2019) Project DG-1300 DG-1000K DG-1000S DG-700 DG-800 Average degree of polymerization P 1221-1380 981-1080 981-1080 651-750 751-850 Apparent density, g / ml 0.46-0.54 0.51-0.57 0.51-0.57 0.53-0.61 0.54-0.60 Whiteness (160 ℃, 10min),% ≥ 78 78 78 75 78 Corresponding table of degree of polymerization, viscosity and K value Average degree of polymerization 2351-2650 1221-1380 981-1080 771-870 751-750 651-750 481-600 401-500 Viscosity, ml / g 222-248 125-138 105-138 87-96 86-94 73-86 62-72 57-64 K value 89-93 70-73 65-67 60-62 59-62 55-59 51-55 49-51

VAE emulsion is short of vinyl acetate copolymer emulsion, it is the emulsion product which uses vinyl acetate monomer and ethylene monomer as raw material with the method of press copolymerization. The characteristics of the process is using outer loop to expose the heat of reaction, the polymer is fast, the capacity is large, the process of polymer is controlled by computer, the product quality is stable, low depletion, little pollution. The product is non-toxic, tasteless, it is environmental protection product which is recommended by the government. VAE emulsion is a kind of milky liquid. Because of ethylene copolymerization monomer, VAE emulsion has the characteristic of inner plasticizing, and filming, weather resistance, adhesive, and compatible, weak acid and alkali resistance. Adhesive basic material VAE emulsion can be used as adhesive basic material, such as wood and wooden products, paper and paper products, package composite materials, plastics, structure. Paint basic material VAE emulsion can be used as inner wall paint, elasticity paint, waterproof paint of roof and groundwater, the basic material of fireproof and heat preservation paint, it also can be used as the basic material of the caulking of structure, sealing adhesive. Paper sizing and glazing VAE emulsion can sizing and glazing many kinds of paper, it is excellent material of producing many kinds of advanced paper. VAE emulsion can be used as the basic material of no-woven adhesive. Cement modifier VAE emulsion can be mixed with cement mortal so that improving the property of the cement product. VAE emulsion can be used as the adhesive, such as tufted carpet, needle carpet. weaving carpet, artificial fur, electrostatic flocking, high-level structure assemble carpet. Product advantages and application scope GW-705/GW-706: The common adhesive with high quality, excellent innitial adhesion, mechanical stability Widely used in paper product, wooden package, cement, cigarette. GW-707/GW-707H: The biggest advantages is its good water resistance in the condition of the static load, it has excellent adhesive Widely used in paper product, package, coil adhesive, high-speed adhesive, water resistance coating. GW-102/GW-102H: It has better adhesive. The compatibility of material is good Widely used in Shoes Adhesive, Clothes Adhesive, Wood, Paper Painting, Furnishing Detail parameters Product Name Solid Content %≥ PH Value Viscosity(25℃) Mpa.s Remain Vam %≤ Particle Size um≤ Dilution Stability %≤ Minimum film-forming Ethylene content % temperature ℃ GW-705 54.4 4.0-6.0 1500-2500 0.5 2 3.5 0 16±2 GW-706 54.4 4.0-6.0 2500-3300 0.5 2 3.5 0 16±2 GW-707 54.4 4.0-6.0 500-1000 0.5 2 5 0 16±2 GW-707H 54.4 4.0-6.0 1000-1500 0.5 2 3.5 0 16±2 GW-102 55 4.0-6.5 3500-4000 0.5 0.2-2.0 3.5 16.5 GW-102H 55.5 4.0-6.5 4000-4500 0.5 0.2-2.0 3.5 17